ELWO: 2010.06.26 19:06:17 |
Üdv! Egy WA63131 bõl másoltam. De F10 et nem találltam benne. FAILURE SHORT DESCRIPTION DESCRIPTION FAILURE DISPLAY F1 connection to temperature sensor open or shortcircuited The failure is set, if the connection to the temperature sensor is open or if there is a short circuit between the two terminals of the sensor. The washing program will be ended without heating. The failure will be displayed at the end of the washing program. On LCD: ERROR 1 F2 The connection with door lock is open The failure is set, if the connection to the door lock is open. The washing program will stop. The failure will be displayed. Supply of door lock will be ON. To start the washing program, the user has to close the door (program starts at once). To continue the program (if failure happens between washing program), the user has to check if the door is closed and press the „Start“-button. If the failure occurs again, the washing program stops. Supply of door lock will be OFF. If the water is in the machine, than pumping 2 minutes. Failure will be displayed again , and it is not possible to start the washing program again. On LCD: ERROR 2 F3 the water level was not reached. - water tap closed - leak in the machine - valve defect The failure is set, if within filling or heating step the water level is below level 1 for the filling time or 4 minutes in heating time. If the failure occurs the first time within a washing program, the current step starts again. If the failure occurrs the second time (twice in succession), the washing program is stopped, and the failure will be displayed. To continue the washing program, the user has to press the „Start“-button. If the failure occurs the third time, the washing program stops, the failure will be displayed, and it is not possible to start the washing program again. On LCD: ERROR 3 F4 the connection to the tacho generator is open or shortcircuited If the washing program is active and the motor control unit gets no signal from the tacho generator, the first time the failure occurs a pause of 1minute is executed. This repeat 3 times. If once happen that motor works O.K. than all previous failure must be deleted. When the failure is detected the 4 time’s the washing program stops immediately. If the temperature is higher that 60°C than cool down with cold water 30 seconds. Then pumping water 2 minutes. On LCD: ERROR 4 F5 the triac is short-circuited The failure is set, if the washing program is active and the motor is working without control of triac. The washing program is stopped immediately. . After 2 minutes try again. If the failure is not present, than forget the first failure and continue work. If is the same failure again, than program stops complete. If the temperature is higher that 60°C than cool down with cold water 30 seconds. Then pumping water 2 minutes. STOP the program. The failure will be displayed. On LCD: ERROR 5 F6 temperature not reached - heater defect The failure is set, if after a heating step the temperature is more than 15°C lower than the rated temperature. The washing program will be ended normally. The failure will be displayed at the end of the washing program. On LCD: ERROR 6 F7 the water level does not fall below level 1 - pump clogged - pump defect The failure is set, if after a pumping step the water level did not fall below level 1. If the failure occurs the first time within a washing program, the current step will started again. If the failure occurs the second time (twice in succession), the washing program is stopped and the failure is displayed. To continue the washing program, the user has to press the „Start“- button. If the failure occurred the third time, the washing program is stopped and the failure is displayed. It is not possible to start the washing program again. On LCD: ERROR 7 F8 The WM not reach max. spin speed (the tapped field relay does not switch) The failure is set, if at the end of the spinning cycle of the testing program the spin is more than 100rpm lower than the rated speed. The failure is displayed after the end of the testing program. On LCD: ERROR 8 F9 Water inside machine (Aqua Stop) The failure is set, if Aqua Stop Sensor makes signal (must be measuring min. 2 seconds). All valves switch OFF, the heater switches OFF and main motor STOPS. After 3 seconds check again. If the failure is not present, than forget the first failure and continue with program. If the failure is still present, than switch ON the pump for 2 minutes and stop WM. The failure is displayed. It is not possible to start the washing program again. On LCD: ERROR 9
|